Skip to main content

OmniMax USA LLC

Home  OmniMax  OmniMotor  OmniDisplay  Absolute Furniture  Cubicles   
Electrical AO2 Version 1
Electrical AO2 Version 2
Lateral File
Panel Components
Pedestals
Raceway
Storage
Work Surface Components

Electrical 8 wire Version 1 Components

We carry AO2 version 1 power components for AO2 panel systems.

 
•Power Packs (8 wire power bus)
•Receptacles (compatible with Version 1, Version 2 and OEM power)

•Power Entries for Base Feed (compatible with Version 1, Version 2 and OEM Power)
•Power Entries for Ceiling Feed (Compatible with Version 1 only)
 
Please note, this product must be installed by a licensed electrician. You must contact local code authorities for use and application for the product.

HMP20-1-xx Power Entry, Base Feed Version 1 & Version 2

Power Entry for Base Feed, 4 Circuit 15amp, Snap in unit. Mounts in Receptacle Opening
 
Available Right Hand (-R) or Left Hand Version (-L) (hand is determined by facing the panel, RH goes Right, LH goes left toward power feed on drywall.
 
Comes with 6 foot 1/2" liquid tight cable. Must be connected by a licensed electrician. This may require modification to the building electrical to be installed correctly.
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 
 

 

 

HMP20-2-xx Power Entry, Ceiling Feed Version 1 & Version 2

Power Entry for Ceiling Feed, 4 Circuit 15amp, Snap in unit. Mounts in Receptacle Opening
 
Comes with 6 foot 1/2" liquid tight cable. Must be connected by a licensed electrician. This may require modification to the building electrical to be installed correctly.
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 

 

 

 

 

 

HMP08-3-ZN Power Pack, 8 wire for 24" wide panels Version 1


Power Pack, 8 Wire for 24" Wide Panels

 

This item has location for one duplex receptacle on each side of the power pack 

 

Mounts in metal raceway under panel.

 


This item can be used for Version 1 power only.

 


 

 
HMP08-x-ZN Power Pack, 8 wire for 24" wide panels Version 1

Power Pack, 8 Wire for 30", 36", 42", 48" or 60" Wide Panels
 
This item has location for two duplex receptacle on each side.
 
Mounts in metal raceway under panel.

This item can be used for Version 1 power only
 
 
 
 
HMP10-x-xx Receptacle Duplex Version 1 & Version 2

Receptacle, Duplex, 15amp, Snap in unit.

Available Circuit 1 (A), Circuit 2 (B), Circuit 3 (C), Circuit 4 Dedicated (D) 
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 
Availble in BU, DT, MT or HF Finish
 
 
 
 
 
 
HMP10-x-xx Receptacle Duplex Version 1 & Version 2

Receptacle, Duplex, 15amp, Snap in unit.

Available Circuit 1 (A), Circuit 2 (B), Circuit 3 (C), Circuit 4 Dedicated (D) 
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 
Availble in BU, DT, MT or HF Finish
 
 
 
 
HMP10-x-xx Receptacle Duplex Version 1 & Version 2

Receptacle, Duplex, 15amp, Snap in unit.

Available Circuit 1 (A), Circuit 2 (B), Circuit 3 (C), Circuit 4 Dedicated (D) 
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 
Availble in BU, DT, MT or HF Finish
 
   
 
 
 
          HMP10-x-xx Receptacle Duplex Version 1 & Version 2

Receptacle, Duplex, 15amp, Snap in unit.

Available Circuit 1 (A), Circuit 2 (B), Circuit 3 (C), Circuit 4 Dedicated (D) 
 
This item can be used for Version 1, Version 2 or OEM Version 1&2 power
 
Availble in BU, DT, MT or HF Finish 
 
 
 
 
 
HMP03-1 Festoon Power Jumper - Panel to Panel Version 1

Version 1 8 wire AO2 power system festoon jumper.
 
This item is used to connect power packs from one panel to another.
 
Unit is mold plastic connectors wtih cable to allow connection from Panel to the next panel in line.
 
 
Please note if you are using this to connect from panel through a connector to another panel, please use the next festoon jumper below.
 
 
 
HMP03-2 Festoon Power Jumper - Panel Connector Panel Version 1

Version 1 8 wire AO2 power system festoon jumper.
 
This item is used to connect power packs from one panel through a connector to another panel.
 
Unit is mold plastic connectors wtih cable to allow connection from Panel through a connector to the next panel in line.
 
 
Please note if you are using this to connect from panel to another panel in line, please use the festoon jumper above.